No announcement yet.

Search Result

37 results in 0.0131 seconds.
miller x

  • jbillingsley
    started a topic 12vs suitcase

    12vs suitcase

    I recently got a 12vs extreme suitcase wire feeder, seemed to work pretty good the first day. But I went to go turn it on for the second time and there’s just nothing!!! I won’t turn on at all. Anybody have any ideas as to why? Or where you can actually get parts from to fix these?? Any help...
    See more | Go to post

  • JakeLB
    started a topic Millermatic 200 CR1 chattering

    Millermatic 200 CR1 chattering

    Hello have a millermatic 200 SN# JE777868. I replaced the CR1 relay because it wasn't pulling by itself all the way to push the contact points over. Now with the new ice cube style if you hold it for more then 2 seconds the points start chattering and it shoots small sparks between points. Seems like...
    See more | Go to post

  • M.I.G. Feeding Troubleshooting Tips By A Warranty Technician

    Hi All,

    My Name is Logan P. Clayton I am a warranty Tech for Miller, Lincoln, Esab, Hypertherm, Hobart, Thermal Dynamics, Thermal Arc, Firepower, Snap-On and just about every other main welding brand you can think of, I am starting a playlist for troubleshooting tips that will be comprised...
    See more | Go to post
    Last edited by LoganpClayton; 12-16-2019, 10:03 PM.

  • FireMed
    started a topic What's this old welder worth?

    What's this old welder worth?

    I picked up this older welder a while back. It is a Miller Del-200 with a Deutz single cylinder diesel engine. Motor is F1L 210D. Serial number is 7652864. I tested the generator and it produced power.
    I cannot attach larger picts. Here is a link to Google drive with the picts of the unit....
    See more | Go to post

  • Is the WC-24 a right fit for me?

    I have the trailblazer (325 EFI w/ Excel Power), and an inverter tig welder (2016 AHP AlphaTig 200x). The plan is to start a mobile welding business with an enclosed trailer. Im looking into getting a WC-24 but i recently discovered what the name meant. Weld Control 24VAC. Does this mean it only runs...
    See more | Go to post

  • Mike yates
    started a topic Miller matic 35 sputtering

    Miller matic 35 sputtering

    Guys in shop complaining about sputtering, but welds look great to me. 85 wire feed welding 1/2 plate on setting 4. 15 to 20 flow rate on 75/25 gas. Same settings for two years. But I have to admit it doesn't "hizzle" like i remember. Just replaced all the diodes with OEM because we had some...
    See more | Go to post

  • ajherhold
    started a topic Miller Thunderbolt crank

    Miller Thunderbolt crank

    100% stick welding novice here.

    What's the crank used for on the top of this thunderbolt welder? Amp adjustment wheel?

    See more | Go to post

  • Walk_The_Cup399
    started a topic Generators


    As of right now Im running a dynasty 200 dx. I use it for small projects using stick and tig, around 155 amp. It runs off 110 but none of the outlets in my townhouse can handle it. So the easy route would be to run a dedicated outlet/breaker for my machine but I rent and have been told by tge wife that...
    See more | Go to post

  • Up-parts
    started a topic Millermatic 350p Help 7

    Millermatic 350p Help 7

    Recently purchased at auction, a nice clean looking MM350p. All cords were removed prior to sale so I worked with the local Airgas and now have all new. I relinked the machine per the manual for 1-phase 240vac and hit the switch. Nothing.. I got Help 7 & 9. I have checked the power supply and it...
    See more | Go to post

  • Miller Bobcat 225 will arc but not weld

    I have a Miller Bobcat 225 that just quit welding. it will arc but not enough to burn a rod. The outlet plugs have power but it doesn't seem to be very strong. Any ideas? Thank you!!

    Leads are all connected well.
    We were welding fence cutting the welder off to cut some pipe and started...
    See more | Go to post
    Last edited by wbullet; 03-24-2017, 02:35 PM.

  • swamper2012
    started a topic Miller Bluestar 2E

    Miller Bluestar 2E

    I'm new too this group. I've recently purchased a older miller bluestar. Looking for any advice on the welder good or bad.
    See more | Go to post

  • No AC frequency adjustment after updating syncrowave 210

    Hello millerwelds forums! I'm hoping someone out there can help me get AC frequency up and running on my syncrowave 210. (My machine doesn't have the spoolmate capability in the bottom left corner, so it's not the latest model)

    Here's the scoop:

    -I hadn't had AC frequency adjustment...
    See more | Go to post

  • modela
    started a topic Help with settings on S-64 Wire Feeder

    Help with settings on S-64 Wire Feeder

    I have a 304 CC/CV and a S-64 wire feeder. I am wanting to weld with MIG using the s-64 wire feeder. I have a manual but I cannot get the welder to run consistently. It runs a few seconds and then the wire sticks in the puddle and the current is shut down. I have another wire welder but I really...
    See more | Go to post

  • Miller The Legend AEAD 200le information needed

    Hi I am new here. I have the chance to purchase a Miller The Legend AEAD 200le gas powered welder/generator. I am seeking any information I can get on this welder. It has low hours, it is in great shape and has always been stored in a garage. I am mainly trying to figure out how long miller made these...
    See more | Go to post

  • parrfam71
    started a topic bluestar 2e

    bluestar 2e

    Hello . My welder welded fine then outta blue it just barely cracked an arc or made power I saw,in parts manual just above the #28 resistor ,a solid wire under a cloth sheath it had a small burn mark so I looked all I found was a piece of black plastic and the wirecwas disconected. I got a rectifier...
    See more | Go to post