How Much The Cost Of This Mig Welder ?

[SCHOONER]

Hi Guys

Came across a MillerMatic 135 ~ 115volt ~ Phase 1 for sale. With cart and Airgas also included.

Tell me what's a reasonable price I should pay for it

Guys talking $500.00 bucks.

Thanks

[SCHOONER]

Here's The Settings



Hey Sberry

1. The Voltage is: (THE HEAT) setting on your welder.
What kind of welding machine do you have ?

2. The (THE SPEED) setting is the rate of speed the wire comes out of your
mig gun handle....

[SCHOONER]

My Reply



Hi Cruizer

First of all thanks 4 your reply.

In ans. to you questions are as follows:

Hard Wire: .030 J.W. Harris "Twenty Gauge Shotgun"
Gas Setting: 12lbs.

That's about it my good man....

[SCHOONER]

Here's What I Got



Hi Cruizer

GAS is: 75/25 I believe its: 75% Argon and 25% Oxigen.

WIRE Diameter: I'm using a .030 tip ~ if that helps you to help me.

Wire Manufacturer: Harris; Shotgun

Something like P J Harris;...

[SCHOONER]

Hi Guys/Gals

I have a Millermatic 135 for the use of mig welding sheet metal; gauages from: 18 to 21

QUESTION(S) PLEASE:

What heat setting and speed would you set your Millermatic 135 to if your welding 19ga.?

Also the following gauages please:...

[SCHOONER]

Hi Beamwalker

What is you approach to over head mig welding?

At what angle do you hold you mig gun?

Thanks guy
GOD BLESS

Schooner

QUOTE: I try to remember H.A.L.T.
Don't get: Too HUNGRY, ANGERY, LONELY or...

[SCHOONER]

Hi Bob

Yeah, I guess your right about angles I just found out today by PRACTICING MY MIG WELDING.

Thanks for you imput BOB
GOD BLESS

QUOTE: No man know just how bad he is till he tries very,very hard to be good.

Schooner ...

[SCHOONER]

Hi Guys (Newbie Here Again)

I'm about to be doing a bit of over-head mig welding.

I'm new at this, done flat and vertical outcome not bad.

I rather get it straight from you expert who've done mig over head.

QUESTIONS PLEASE:

...

[SCHOONER]

Hi Guys (newbie here)

I got my MillerMatic135 and its GREAT for my car restoration.

What I want to know please:

How much gas pressure do I use to mig weld: 18 gauage sheet metal ?
My dial speed is: 4
My voltage is: 4
I got the air pressure...

[SCHOONER]

Hi Guys Newbie here


I just started PRACTICING with my MillerMatic135 today 7/23

I'm using .024 ER70S-6 wire. Practicing on:18 gauage s/metal.

I have my air pressure gauage set on: 10 pounds.

QUESTIONS PLEASE:

1.What...

[SCHOONER]

Hi Guys (Newbie Here)

I'm about ready to start practicing with my new MillerMatic135.

Did Elec. & Tig welding for many yrs. but NEVER did Mig

I'll be welding thin sheet metal 20 to 24in. gauage.

I was wondering why is it that the...

[SCHOONER]

Hi Newbie here

I'm going to be mig welding on my '66 Mustang Convert also.
Can you kindly tell just WHY ER70S-6 is BEST to use
Is this a SOLID CORE WIRE or FLUX CORE WIRE


THANK YOU
GOD BLESS

Schooner...

[SCHOONER]

Hey Guy

Thank you for your input.
I will take what you said un consideration.

Thanks again
GOD BLESS

Schooner

[SCHOONER]

Hi Russ

The weld-thru spray prevents the area from rusting-up after I finish mig welding the 18ga. sheet metal.

Its a great way to stop rust after welding.
And the seam sealer is a protection over the weld when its completed.

Other than that Thank...

[SCHOONER]

Hi Guys

I'm a newbie to mig welding. However, I've done elec./tig for some 16yrs. But unfortunatly, I never needed to mig weld. I bought a Millermatic135.
So here I am.

I'm about to take the challenge an restore my ' 66 Mustang Convert.

Here's what...