Announcement

Collapse
No announcement yet.

Search Result

Collapse
25 results in 0.0186 seconds.
Keywords
Members
Tags
  •  

  • Slag
    replied to Miller 2050 torch options
    Scott V:
    What torch it that in the picture?
    Will it fit on the 2050?

    SBerry:
    Thanks for the suggestion. I think I tried adjusting air up and down but I try it again just to make sure.
    See more | Go to post

    Leave a comment:


  • Slag
    replied to Miller 2050 torch options
    I tried setting the amps down as low as possible. I also tried cutting the air pressure down to the minimum as well.

    Using a brand new electrode and tip I still can't get the kerf to where I would like it. I also have to travel a little too fast for any real precision work.
    ...
    See more | Go to post

    Leave a comment:


  • imported_Slag
    started a topic Miller 2050 torch options

    Miller 2050 torch options

    I have a 2050 Plasma cutter with the 55 torch that came with it.
    I am very satisfied with the 55 torch on thicker material but I can't seem to adjust the machine down enough to get a real nice thin kerf on thinner material.
    I bought the 35amp tips for it but I still can't get the kerf...
    See more | Go to post

  • Slag
    replied to bucket welding photo
    Hey fun4now,
    what kind of pups are they?

    I assume a breed of mastiff

    Any pictures of their parents?
    See more | Go to post

    Leave a comment:


  • Slag
    replied to Cutting advise
    I have a portaband that I use all the time.
    You can get one for under 300, and it will last forever.
    If your careful you can make some very good square cuts.
    See more | Go to post

    Leave a comment:


  • Slag
    replied to Spectrum 2050
    Mine does that when I forget the ground clamp. Takes me several attempts of "what the heck?" then I proceed to call myself choice names, clamp on the ground and things are good again.
    See more | Go to post

    Leave a comment:


  • Slag
    replied to TB 302 with kohler or TB Pro 350D
    From my experience, I look at the longevity of the diesel as a bonus. You should save more than the initial cost of the diesel in fuel alone over the life of the machine.
    See more | Go to post

    Leave a comment:


  • Is the ICE-55c torch that comes with the 2050 a HT torch?

    HAWK, Do you have the ICE-55c?
    See more | Go to post

    Leave a comment:


  • imported_Slag
    started a topic 14 pin connector?

    14 pin connector?

    What is the most common use of a 14 pin connector?
    I have one on my TrailBlazer that I assume is for running a wire feeder?

    But, I also have a MM250 with the 10 pin module for running the 30A spool gun. The 10 pin module also has a 14 pin connector. What would this be used for...
    See more | Go to post

  • I was leaning towards getting the Miller but after reading about the grinding button on the Optrel I will probably have to go with it.

    I don't think I could handle having to turn down the sensitivity and then back up to where it was every time I went from weld to grind and back to weld....
    See more | Go to post

    Leave a comment:


  • Time for a good ol' fashion whippin!!!

    Seriously, the law should be brought in on this one.
    I've had "jokers" change my heat setting before, but adding something to the fuel is WAY beyond a joke.

    He would pay one way or the other.
    See more | Go to post

    Leave a comment:


  • Slag
    replied to Bernard consumables
    GARAGEGADGETS,
    that is definitely something to consider.
    However, I may be forced to sell to help pay for the 251.

    Would be nice though...
    See more | Go to post

    Leave a comment:


  • Slag
    replied to Bernard consumables
    That's one place I haven't tried. I have an Airgas close to where I work. I'll give them a call and see if they stock Bernard.

    Thanks for all the help...
    See more | Go to post

    Leave a comment:


  • Slag
    replied to Bernard consumables
    I am now the owner of a brand new MM251.
    My old machine, which I haven't even ran 10lbs through is a MM250. I plan on selling it, but I am undecided on whether to sell the M-25 that came with the new machine with it.

    I am leaning towards keeping the Bernard. I am just a little...
    See more | Go to post

    Leave a comment:


  • Slag
    replied to Bernard consumables
    Thanks for all the responses.
    I have looked at both websites suggested above and it looks like both carry the tips I need.

    Scott V,
    Which one of the guns are you saying has the better trigger and nozzle/tip setup?

    I will probably never use spray-arc. What...
    See more | Go to post

    Leave a comment:

Working...
X