Miller Sych 250 no weld power?

[Emrlddvr]

Don't you guys just hate it when someone asks for help and then doesn't perform the test that the group says to? I have finally gotten to it. In stick mode there is no weld power. The AC/DC AMP meter pegs to full when the welder is turned on irrelevant to which mode it is set to. Second, when the hall...

[Emrlddvr]

Thank you for the response. I will try the test scenarios in the morning. I am in Poteau, OK

[Emrlddvr]

I'm usually self sufficient however, not this time. Just bought Synchrowave 250, knowing it was inoperable. It diagnosed for the previous owner by Airgas. They indicated that the hall devise was defective and those chose to replace the machine. I had the device rebuilt by Nyco Systems and installed...

[Emrlddvr]

Youngsters projects

we just finished a camp for under 16 yr olds. 1 week, will be 2 weeks next yr. We started them doing overlays on a 2.375 diameter pipe about 4 inches long. Do the overlays longetudnally not around the pipe. Cut the guys some caps to weld on both ends and have them...

[Emrlddvr]

I'll try to let you know the longevity of them. I am getting ready to cut a bunch of 1" solid

[Emrlddvr]

Bob... Thanks I found that also shortly after my post. I should research a little before talking. My local welding supply displays an evo cutting a 3" solid!

[Emrlddvr]

Just recieved my case of ten blades from a vendor on eBay. Cost 35 bucks each and I was very pleased with the $$. However after looking one over good is says on the blade 1/4 max material thickness. I have a new Evolution chop saw (cold saw for lack of a better description). I understand that the saw...

[Emrlddvr]

Looking for help again. Going to bid a single rail 3 foot tall pipe fence with 4 1/2 sched 10 pipe. What reccomendations do you have for quoting the labor? Have to drive the posts, cut the saddles weld top rail on. I fugures about an hour per section. A section being on post and one rail section 12...

[Emrlddvr]

One step further

Great programs. Let's go one more step. For those of us who cut most copes on a chopsaw or bandsaw has anybody seen a program to give us the corrct angle measurements for cutting saddles?

[Emrlddvr]

Great... Again you guys saved me a bumch of work. Thanks again

[Emrlddvr]

I am going to build some pipe wraps/templates with solidworks in a few days. I will be happy to share the files. You would print them off on heavy paper then use them like a pipe wrap. Or as I am going to do use the prints a templates to cut the wraps out of pipe wrap material. Anyone have suggestions...

[Emrlddvr]

A few months ago the wire feed on my 185 mig quit. Took it to service center (I new better but did anyway) the charges me $85 to look at it and tell me that it needed a new control board at a cost of almost $400. We all know that you don't have to replace a whole board to fix the problem. So I talked...

[Emrlddvr]

I assumed that it would be difficult. Just pulled an alll nighter to these things finished. No problem MIG worked just fine. Thanks to all for the help.

[Emrlddvr]

Boy do I luv this place... Thanks for all the input. Finished up last night with the old abrasive. What about reversing the polarity of the MIG. I run a miller suitcase that I can reverse it on. btw Building oilfield pipe racks. saw a blip somewhere (prob here) ablout a blade called Freud Diablo Steel...

[Emrlddvr]

Brand new here and need some adult supervision! Working with 3 1/2 drill stem, not pipe. We have a brand new Evolution cold saw. Works great except it will only make about 4 cuts before blade is dull. At $150 each I can't take anymore. Is drill stem hardened? Advice please. Next any friendly advice...