thanks
Yep, It was a tiny piece of junk way back in the tip of the gun. This was the first time I had that happen. Thanks everybody for the help. I stay so busy that the little things go overlooked. Thanks again.
13 results in 0.0069 seconds.
-
MM 211 having problems
Hi all, I am having problems with welding anything steel, My gun cap is arcing to the metal I am welding. I have never had this happen before. I am running 030 solid wire,75/25 gas ,220 power,I have tried auto set up and manual set up.Not alot of hours on this machine (aprox30) My MM172 was much more... -
this is what I use
I have a 211 and have ran it wide open for long beads and run it on a double pole 30amp braker.its wired with # ten wire.So if I was you I would go with what I used.If you are planning on running something else that will require more power it might make it better to...Leave a comment:
-
clean air
I have mine mounted to the handle of my compressor and run a small inline one right at the plasma cutter unit,Works great!
Leave a comment:
-
welding on 110
Well I put the 211 thru some tests on 110. It did well ,I did not have any
problems as long as I stayed under what would draw 20 amps.I could get it to trip on 1/4 plate and larger,But for 1/8 inch angle it was fine.I think its all about knowing where your limits...Leave a comment:
-
Hi KillerBee,
I was welding with 220,Never tried it on 110. I have a subpanel with three
twist locks 1- for the 211,1-for the plasma, and 1- for the 200 dx. I leave
everything plugged in and just turn the brakers on and off . This way I don't
wear out my switches,plus...Leave a comment:
-
Wow !!
Did alot of welding with my 211 today,and all I can say is WOW!!!
This thing is a beast.I was very pleased with the duty cycle.I was welding
1/2 plate to 1/4 plate for a scraper blade and it rocked right on.Some beads
were 16" long and using auto set with...Leave a comment:
-
redneck welder
You know your a redneck welder when your gear costs more than your house.
Leave a comment:
-
I use bosch battery chargers on a modified sinewave inverter and its fine as long as the truck is not running,but when I crank the truck they freek out.
not sure what happens but they are not happy so I had to change to a pure
sinewave inverter.Now all is well if the truck is running...Last edited by Kenny Brutcher; 11-27-2009, 10:33 PM.Leave a comment:
-
Yes to the 211.SSJ is right on, the more welder you get the more you can do.
The spoolgun is the stuff.I got 211 and spoolgun and love it.Not real pricey
for what it is.I went from a 172 to a 211 and was a needed upgrade.I have never used the 110 option but its there for small jobs.Besides...Leave a comment:
-
water cooled VS air cooled tig torch
Ok Folks,I am wondering if water cooled is where its at? I have been
welding with a air cooled torch on a D 200.I do some times have a hard time
holding on to a very hot torch after some long beads.I am gonna build a welding hand truck and was wondering if i should plan on a coolmate 1...Last edited by Kenny Brutcher; 11-27-2009, 10:03 PM. -
Thanks for all the replys,I think that I will go with air fittings as I never leave the tank on any way.Alwayse moving them any way.I think it would be cool
if Miller put a fitting that would just let you push the hose right into it,like
a o ring fitting that all you have to do is push...Leave a comment:
-
shielding gas hookup
Hi all.
New here and I have been welding for many years and I was wondering if I can use air fittings to make a quick disconnect for my shielding gas connection? I have two portable rigs and It would be great if it would work.
The rig is on a welder handtruck and if I could get...
Leave a comment: