Announcement
Collapse
No announcement yet.
Forums
Collapse
Collapse
-
How to purchase Miller service manuals
Hello, I see several threads related to miller welder service manuals but am curious if they are available to non miller service personnel. I was told by a local dealer that they can not sell the technical manuals. I have several XMT 304's and 350's. Some work and some are for parts. I help a friend...
-
I need some help fixing old AirCo 250 TIG machine.
AIRCO 1341-0158 TIG WELDER HELIWELDER. INCLUDES LINCOLN MAGNUM SYSTEM MONITOR. 250 AMP MAX AC/DC. BACK DRIVE VINCE.
I have one of these machines and the HF start wasn't working. Chased it down to CR1 (12VDC relay) and used a brass brush and contact cleaner to clean everything I could see. Removed the HF bullets and cleaned and gapped them. It...
-
power wave 355 Tig connections
Hello,
Does anyone know how to connect a Tig torch and foot control to power wave 355 / power feed 10 with a control box?
the manuals for the welder and the feeder both say that GTAW is supported but they conveniently forgot to describe how you would set it...
-
Trouble welding thin sheetmetal Millermatic 180 mig
I'm restoring a '63 Impala and have had to replace the floor pans (18g). I using 0.024 wire and 75/25 shield gas. I'm running the voltage 2-2.5 and 30 on the wire feed. 18 CFH for gas flow. To start with new metal against partially thinned out metal is a challenge as I'm always burning through on the...
-
Blue Star 2e 1980’s run problems
Starts with full choke. Runs 15-30 seconds and dies. Will repeat and die
any general thoughts
OH160 Tecumsek j model
-
Miler Big Blue 400
Hi, I don't run my big blue very much. I'm curious if I can crank it up and just let it run several hours here and there without welding or using the a/c side and just let it run on high idle to exercise it. Or do I need to plug in a fan or something into a 110 socket just to draw some power off of...
-
Onan engine parts, where to find them
The onan engine in my hobart champion 16 has developed a rod knock. I'm having trouble finding parts for it. Anyone know places to find parts or even replacement engines to get this up and working again?
-
Tactile Push button micro switch Synrowave 350 electronics board
SW1 - SW4 on the bread board have all failed. The rubber covering the tactile micro switch has turned to mush which means I can't change the various programs, ie: Tig, Stick, etc. Its a simple 8.4 x 8.4 x 3.45 mm 4 pin soldered connection, but I can't find a replacement. Can anyone tell me a part...1 Photo
-
synchrowave 200 start problem
I have a new to me synchrowave 200 that sometimes takes 3-5 mashes on the foot pedal to start an arc when on TIG. I have set the spark gap to .008 and the contacts look to be in good shape. Pedal works fine once the arc starts so I think its OK? Any ideas??
-
Tig Cart, one or two 9” tanks?
Designing a cart for my Dynasty. Any real need for two tanks?
Mig I’d do two but tig?...
No content found
Show More
Please log in to your account to view your subscribed posts.
What's Going On
Collapse
There are currently 90 users online. 2 members and 88 guests.
Most users ever online was 15,465 at 04:37 PM on 12-31-2018.
Miller Welding Discussion Forums Statistics
Collapse
Topics: 35,892
Posts: 357,244
Members: 72,746
Active Members: 137
Welcome to our newest member, SAMCH.
Forums
Collapse
Top Active Users
Collapse
There are no top active users.
Latest Topics from Friends
Collapse
There are no results that meet this criteria.