Announcement

Collapse
No announcement yet.

Good deal for Millermatic 175 mig on Ebay

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Danny
    replied
    Originally posted by Sundown View Post
    The MM180 is available in the middle of US (Miller likes to be quiet about releases until it's available nationwide which will be by the first of the year according to my rep.), it is also being sold right now on Ebay by IOC. From what I understand there is quite a bit more than just the +5 amps, I know for sure that there is a means (switch?) to disable the WST feature (a very good thing IMO) plus other stuff we don't quite know about. I owned a MM175 (for a few months) some time back and If were me I would wait until I could test drive the new MM180, the Lincoln 180C & T, & the HH187 before buying.
    One major improvement on the MM 180, over the MM 175, is arc starts. The MM 175 is somewhat stickout sensitive. The MM 180 on the other hand will fire off a good arc start everytime, even with a 1/2" stickout. I also noticed in wire speed tracking mode, the MM 180 is much easier to dial in a solid metal transfer on, then the MM 175. Supposed too, there have also been some improvements made to the output that I haven't got to see yet, because they were done after my field testing of the unit. Hopefully soon though, I'll get my quick look at one of these updated units to check out how much of an improvement was made.

    On the MM 180 to go from wire speed tracking mode, to constant wire speed mode, requires a little more then flipping a switch. As a matter of fact, there is no switch. To accomplish the task of going from wire speed tracking to non-wirespeed tracking mode, requires the following procedure:
    1. Power down unit.
    2. Turn wire speed dial to mininum setting.
    3. Turn voltage dial to maximum.
    4. Pull gun trigger, and hold.
    5. Power up unit, while still holding gun trigger down.
    6. Hold gun trigger for at least one second, then release it.


    To put the unit back into wire speed tracking mode, requires following the same procedure, except you turn the wire speed and voltage dials in the opposite directions.

    Leave a comment:


  • Sundown
    replied
    Originally posted by dongill View Post
    MM 180 is apparently MM 175 + 5 amps + $100. Not yet available in the US.
    The MM180 is available in the middle of US (Miller likes to be quiet about releases until it's available nationwide which will be by the first of the year according to my rep.), it is also being sold right now on Ebay by IOC. From what I understand there is quite a bit more than just the +5 amps, I know for sure that there is a means (switch?) to disable the WST feature (a very good thing IMO) plus other stuff we don't quite know about. I owned a MM175 (for a few months) some time back and If were me I would wait until I could test drive the new MM180, the Lincoln 180C & T, & the HH187 before buying.

    Leave a comment:


  • DDA52
    replied
    I dunno...my LWS still has a new HH175 on display. Bet they still have a few MM175's in a year as well.

    Leave a comment:


  • dongill
    replied
    MM 180 is apparently MM 175 + 5 amps + $100. Not yet available in the US.

    Leave a comment:


  • MAC702
    replied
    Big push to get rid of them now that the MM180 is out?

    Leave a comment:


  • dongill
    started a topic Good deal for Millermatic 175 mig on Ebay

    Good deal for Millermatic 175 mig on Ebay

    Ebay Item # 230046967036 is a new Millermatic 175 mig welder for $679.95 with free shipping and no tax. 7 left to sell. I have no connection to the seller. I just bought one.
Working...
X