Announcement

Collapse
No announcement yet.

Custom Jetski Stands

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Custom Jetski Stands

    I'm building these jetski stands. 2" (1/8 wall) angle & square tubing, pneumatic casters which are ideal for travel over uneven surfaces & swivel hinged bunks which will conform to any hull design.
    Attached Files

  • #3
    looks good man.. are you located in boston proper?
    American By Birth, Union by Choice!

    4th generation Pipefitters LU 537

    SpeedGlass 9000x Hood
    Miller Elite Titanium 9400 Hood

    Comment


    • #4
      Looks good

      I like it, nice, clean, and painted. I know nothing about watercraft but I'm sure they are more than stout enough to handle the load. Just curious, is that your own design or did you improve on something already available?

      Comment


      • #5
        Those are some good looking welds. What kind of machine do you use?

        Comment


        • #6
          Originally posted by DamageInc537 View Post
          looks good man.. are you located in boston proper?
          Thanks brother. I'm in Quincy.

          Pipefitters LU537 member also.
          Last edited by Petron; 02-25-2010, 06:45 PM.

          Comment


          • #7
            Originally posted by willy View Post
            I like it, nice, clean, and painted. I know nothing about watercraft but I'm sure they are more than stout enough to handle the load. Just curious, is that your own design or did you improve on something already available?
            Earlier models, 1996-2000 can weigh anywhere in the range of 400-600lbs. The newer models weigh upward of 850lbs.

            I belong to a jetski forum & quite a few members have purchased my stands and they're placing all model jetskis on it with no problems. The pneumatic casters have been very popular, gone are the days of pushing our skis & getting nowhere, these casters make it almost 4WD

            Yes, it's my design, I got sick of the standard design that doesn't allow any comfort when working on the hull or you cannot push the jetski with casters similar to that of my sons Thomas the Train toys.

            Comment


            • #8
              When fabricating my stands having short off-cut pieces that end up being too short for the next stand is inevitable.

              So what to do with short off-cut pieces?

              After speaking with my local jetski dealer who purchased a couple of my other stands we threw around some ideas & my other design was born.

              These are a couple stands I'll be delivering sometime this week.

              Height = 14"
              Width (caster to caster) = 24"
              Bunk to Bunk = Varies from 18"- 20"
              Length = 48"

              Fabricated with my signature pneumatic casters.
              Attached Files

              Comment


              • #10
                The stands look good. Do they come in different colors?
                Nick
                Miller 252 Mig
                Miller Cricket XL
                Millermatic 150 Mig
                Miller Syncrowave 200 Tig
                2-O/A outfits
                Jet Lathe and Mill
                Jet 7x12 horz/vert band saw
                DeWalt Multi Cutter metal saw
                Century 50 Amp Plasma Cutter
                20 ton electric/hydraulic vertical press
                Propane Forge
                60" X 60" router/plasma table

                www.youtube.com/watch?v=jTu7wicVCmQ
                Vist my site: www.nixstuff.com
                and check out some of my ironwork and other stuff

                Comment


                • #11
                  Look through the photo’s again I bet you will find your answer about the colors.

                  Comment


                  • #12
                    Originally posted by Rick C View Post
                    Look through the photo’s again I bet you will find your answer about the colors.
                    I was kidding
                    Nick
                    Miller 252 Mig
                    Miller Cricket XL
                    Millermatic 150 Mig
                    Miller Syncrowave 200 Tig
                    2-O/A outfits
                    Jet Lathe and Mill
                    Jet 7x12 horz/vert band saw
                    DeWalt Multi Cutter metal saw
                    Century 50 Amp Plasma Cutter
                    20 ton electric/hydraulic vertical press
                    Propane Forge
                    60" X 60" router/plasma table

                    www.youtube.com/watch?v=jTu7wicVCmQ
                    Vist my site: www.nixstuff.com
                    and check out some of my ironwork and other stuff

                    Comment


                    • #13
                      Nice work man, if you dont mind me asking. how much can you sell one of those for?

                      Comment


                      • #14
                        Originally posted by Nitto9 View Post
                        Nice work man, if you dont mind me asking. how much can you sell one of those for?
                        I sell them for $199.00

                        I'm a member on greenhulk.net ( http://greenhulk.net/forums/member.php?u=16422 ) a jetski forum & had a few members from MD., FL., IL., want them.

                        Shipping costs were insane until a friend of mine mentioned Greyhound Shipping. Their shipping cost is generally $80.00. It surely opened the door to move my stands outside the New England area.

                        Comment


                        • #15
                          In the triangle area under the support frame how did you weld that together?
                          Attached Files
                          Fab Tech

                          Comment

                          Working...
                          X