Weekend Stock Rack

[JHCHOPPERS]

I finally got around to finishing the stock rack for the new shop. Since I got most of the ideas for it here, I thought I would post some pics.

[uncle johnny]

thats a nice looking storage rack

you also do some nice work on the bikes didnt know there were any bike shops in maryville



johnny

[bob_e95482]

Somehow I missed this one till I saw it today on Powerclick. Awesome job!

[Bert]

JH,
wow, wish I was that mechanically inclined to get parts and make my own cnc!!! Good job, thanks for the pics, and can't wait to see more stuff from you

[smooth72]

Thanks, I will not use Ramos platting again. Lots of grindig scraches and poor plating.

[JHCHOPPERS]

What chrome shop did you use in Oklahoma? From time to time I need items chrome and I have not been happy with my last chrome Job.

I went through every chrome shop in the St. Louis Area, long lead times, bad chrome, bad attitudes, ... A friend of mine recommended these guys and I have been very pleased with them.

Diversified Plating Ltd
(405) 236-0545 2109 W Sheridan Ave
Oklahoma City, OK

[smooth72]

Bert: The Dash Cover is made from T6061 and CNC Machined in my shop, then chromed plated down in Oklahoma ( 100% Made in the USA !!! )

Plasma... In the works now, I just got a Miller Spectrum 375 and it works great. Starting to design and layout a small CNC XYZ Table (36 x 24 x 5) for sheet metal parts. I'll let you know how this turns out...

What chrome shop did you use in Oklahoma? From time to time I need items chrome and I have not been happy with my last chrome Job.

[JHCHOPPERS]

what kind of cnc xyz? Not a plasma cam, is it?
thanks for the info

The CNC XYZ will be a JH Special... LOL. I have been collecting parts(stepper motors, drivers, linear slides, lead screws, belts, pullies, bearings, power supplies, ect) for a while now and have what I think is enough stuff for a small table 24 x 36 x 5. MasterCAM for the parts/design work and Mach3 for the CNC Controller. I plan to use the Plasma CNC Table for Gas Tank Pannels, Frame Gussets and just plan FUN. Sheet metal parts that need to be cut over and over and over again.

[Bert]

what kind of cnc xyz? Not a plasma cam, is it?
thanks for the info

[JHCHOPPERS]

ok...I'm awstruck. Beautiful work!!! Dash cover: how did you "engrave" it?
plasma?
bert
hawaiianmetalworks@hotmail.com

Bert: The Dash Cover is made from T6061 and CNC Machined in my shop, then chromed plated down in Oklahoma ( 100% Made in the USA !!! )

Plasma... In the works now, I just got a Miller Spectrum 375 and it works great. Starting to design and layout a small CNC XYZ Table (36 x 24 x 5) for sheet metal parts. I'll let you know how this turns out...

[Bert]

ok...I'm awstruck. Beautiful work!!! Dash cover: how did you "engrave" it?
plasma?
bert
hawaiianmetalworks@hotmail.com

[wireburner]

that is a NICE bike

[JHCHOPPERS]

Do you work on PARTS for bikes (custom license holders, etc) or do you do the whole bike?

Bert, we do custom parts for Harleys and whole bikes(ie: Harley Chops, not bike kits) We are a small shop, just doing it on the side... You can see all this stuff on our website. http://www.jhchoppers.com

This is our Softail Dask Cover


Here is a 1997 FXSTC we did after a full Chop and make over.


Thanks,
Joel

[Bert]

cool, thanks!

[wireburner]

yep thta is it