Announcement

Collapse
No announcement yet.

Help with TIG welder decision

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • modela
    replied
    Lift arc question

    I have a foot pedal on the unit. The local guy told me that I should advance the foot pedal when using the lift arc. Can anyone give me more specific instructions than what is in the manual.

    Thanks,

    Jim

    Leave a comment:


  • tasslehawf
    replied
    Originally posted by modela View Post
    I have used the lift arc and made it work but I like the high frequency start better. At least it would have been nice to have both.

    Jim
    lift arc is good if for some reason you don't have a remote or the ability to use one.

    Leave a comment:


  • modela
    replied
    I have used the lift arc and made it work but I like the high frequency start better. At least it would have been nice to have both.

    Jim

    Leave a comment:


  • Broccoli1
    replied
    Originally posted by modela View Post
    By the way, I fired up my Maxstar 200 STR yesterday. It is the first time in years that I have used a DC stick welder. It was really smooth and nice. I also used the lift-arc on the unit and welded a little bit with the TIG. Too bad it doesn't have AC. Nice little welder, though.

    For those who are more experienced, how do you rate the lift-arc versus the high frequency start? I have been taking a TIG class at a local community college and using a big Miller water cooled tig and so the Maxstar and the older Syncrowave are my only reference. Somehow I keep thinking that I am going to ruin the Tungsten when using the lift arc. Also, the manual doesn't tell much about what amps you use when starting the lift arc.

    Jim
    "Lift-Arcâ„¢ allows the tungsten to be placed in direct contact
    with the metal to be welded. As the tungsten is lifted off the
    part, the arc is established. This is sometimes referred to as
    touch start. Little if any chance of contamination is possible
    due to special power source circuitry. When the Lift-Arc switch
    is activated, lower power level is supplied to the tungsten
    electrode. This low power allows some preheating of the
    tungsten when it is in initial contact with the part. Remember
    hot tungsten is a good emitter of electrons. This power level
    is low enough not to overheat the tungsten or melt the work
    thus eliminating the possibility of contamination. Once the
    arc is established the power source circuitry switches from
    the Lift-Arc mode to the weld power mode and welding can
    commence. Figure 2.34 illustrates the proper techniques to
    use with the Lift-Arc starting method.
    Figure"

    http://www.millerwelds.com/education/TIGhandbook/

    Chapter II

    Leave a comment:


  • modela
    replied
    More Tig Stuff

    By the way, I fired up my Maxstar 200 STR yesterday. It is the first time in years that I have used a DC stick welder. It was really smooth and nice. I also used the lift-arc on the unit and welded a little bit with the TIG. Too bad it doesn't have AC. Nice little welder, though.

    For those who are more experienced, how do you rate the lift-arc versus the high frequency start? I have been taking a TIG class at a local community college and using a big Miller water cooled tig and so the Maxstar and the older Syncrowave are my only reference. Somehow I keep thinking that I am going to ruin the Tungsten when using the lift arc. Also, the manual doesn't tell much about what amps you use when starting the lift arc.

    Jim

    Leave a comment:


  • Broccoli1
    replied
    Originally posted by tasslehawf View Post
    And excellent service/customer service.
    Indeed

    guess I'll have to wear blue here shortly

    Leave a comment:


  • tasslehawf
    replied
    Originally posted by FusionKing View Post
    Just stirrin' the pot dude...

    To me made in USA makes it superior without question...made in my town would be even better
    And excellent service/customer service.

    Leave a comment:


  • FusionKing
    replied
    Originally posted by Broccoli1 View Post
    How is it superior quality?

    Just stirrin' the pot dude...

    To me made in USA makes it superior without question...made in my town would be even better

    Leave a comment:


  • Blue Collar Moto
    replied
    OOOps. Posted on wrong thread. Sorry.
    Last edited by Blue Collar Moto; 04-06-2008, 02:25 PM.

    Leave a comment:


  • c neck
    replied
    i got the dynasty dx for aluminum and its the best
    but dont forget its a great stick welder to i use it on the
    road all the time for steel and stainless stick, 2 leads a 50' #10 ex.
    cord a couple addaptors for 110 and 220 and some rods
    and it all fit in the front seat of the truck
    you will not be sorry with this welder got mine at cyberweld .com
    no shipping or tax

    Leave a comment:


  • 505HotRod
    replied
    The inverter welder like the Dynasty is the way to go. The Syncrowave doesn't have adjustable AC frequency or a pulser (10pps is hardly a pulser compared to the 250 pps on the Dynasty 200DX). The power of blue. Dream it, weld it.

    Leave a comment:


  • Bert
    replied
    KBFab, just sick man.......just sick.....

    Leave a comment:


  • Bert
    replied
    Originally posted by FusionKing View Post
    ...if you don't believe me just read about 1000 of Fun-for-now's posts!!!!
    Aww...c'mon, don't pick on the guy!!!!!!!!!!!!!!!!!
    (I thought he had 2,000 posts on it!!!!!!)

    Leave a comment:


  • Broccoli1
    replied
    How is it superior quality?

    Leave a comment:


  • FusionKing
    replied
    I sure couldn't tell you if it's worth it. When I bought my Dynasty last fall I don't guess I even knew TA HAD a 200 out...all I ever saw was 185's.
    I will say in a pinch which I get in fairly often I use every bit of juice my Dynasty has got...200 amps and 250 hz and have used it there for SEVERAL minutes untill the part got enuff heat built in to back down. I have welded in the middle of the bottom of workboats with 1/4" thick hulls with a bulkhead t'eed right off from there above where I was welding and It performed FLAWLESSLY.
    It does so well I am starting to think about ending my mobile welding and just stay in the shop except for my very favorite customers. I am sick of seeing customers check out my stuff and then go get a machine for themselves Just seeing that little box [email protected]$$ so hard makes a lot of people just sure as heck they can lay down a bead like me.
    What's even stupider LWS sells them a syncrowave after that because that's what they are pushing...they say I'm the only guy using a 200 Dynasty THEY know
    If you do get the TA just remember this is a MILLER board and you will still ALWAYS wonder if you would have been better off investing in a USA made product of superior quality and will more than likely have welder envy...if you don't believe me just read about 1000 of Fun-for-now's posts!!!!

    Leave a comment:

Working...
X