Announcement

Collapse
No announcement yet.

Tips for the wire welder

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Handy560
    replied
    Egg..

    Thanks Hank, never thought of that.

    Leave a comment:


  • hankj
    replied
    Another common feeding problem with cored wires is too tigh of a wire feed tension adjustment.

    The construction of the wire is such that too much tension on the feed roller will egg the wire. When that egged section hits the tip, it either won't feed at all, or it slows down. That usually results in burn back and a ruined tip.

    Pop your wire out of the drive and look closely at it with a magnifier.

    Hank

    Leave a comment:


  • Vicegrip
    replied
    I don't know about the 180 but my 135 calls for a larger liner when using flux core. One for .023 and one for .030 and .035 IIRC. That might have been the problem.

    Leave a comment:


  • Handy560
    replied
    Flux core

    I have done a bit of welding with a mm180 and flux core wire. What I noticed right away is that it really doesn't like the hose to be curled at all. As soon as you loop or curl the hose it slows down the feed which usually welds the wire to the tip.

    There must be more drag on the liner than with the solid wire.

    I went to great pains to maneuver the unit in such a way that the line was as straight as possible and then no problems...

    Leave a comment:


  • welderman23
    replied
    Originally posted by bryce_burden View Post
    I had the same problem here recently with flux-core wire in my grandpas SP-135. I was attaching some rolled wire onto some panels for chickens, the tip kept plugging up, and after several times of taking it off and cleaning it out, I got mad, fired up the old Thunderbolt and cranked her down real low, grabbed some 3/32" 7014 and went to work. This proved to work so much better. Ran out of time that day so brought the panels into school the next day and finished them with a MM210 (.035 wire, 100% CO2). After this experience, I wasn't to impressed with the flux-core process. I guess like everything else, it takes some getting used to.
    ..................MM210 will spoil you ....you will see when you go back to flux core...
    was used to using nice welders at work ,and was always taking stuff into work to fix/break it .then i go home and weld with my 90 amp fluxcore machine form harborfreight(yeah its blue ,but it aint the same), and im like ....dude this thing sucks. it makes me wanna sell my truck to but a welder ,then i think about how well i can drive a welder home from the bar at 2oAM

    Leave a comment:


  • Gsd34me
    replied
    Thanks guys!

    Leave a comment:


  • bryce_burden
    replied
    I had the same problem here recently with flux-core wire in my grandpas SP-135. I was attaching some rolled wire onto some panels for chickens, the tip kept plugging up, and after several times of taking it off and cleaning it out, I got mad, fired up the old Thunderbolt and cranked her down real low, grabbed some 3/32" 7014 and went to work. This proved to work so much better. Ran out of time that day so brought the panels into school the next day and finished them with a MM210 (.035 wire, 100% CO2). After this experience, I wasn't to impressed with the flux-core process. I guess like everything else, it takes some getting used to.

    Leave a comment:


  • doobie
    replied
    Whe using5/64 flux core,i only use one every couple of jobs,but i also use nozzle dip which helps to keep the spatter from building up as it wipes off easily.

    Leave a comment:


  • abprt
    replied
    changing tips when using flux core wire

    Make sure that you blow out you liner from tip towards drive rolls often. The build up of dust inside the liners when using flux core wire is common and it could lead you to believe that the tips are bad. Run a torch tip cleaner through you welding tip also could help. While using an automated machine, tips lasted at least eight hours of continous welding while using at least 400 amps on 3/32 dia. wire. Dust build up while using flux core wire is a lot worst that when using solid wire with gas.

    Leave a comment:


  • aametalmaster
    replied
    Try a wiper on the wire before the rollers to catch some junk. A small piece of felt or scotchbrite and a wire clip will work. Also some of the flux may be leaking out causing the gunk...Bob

    Leave a comment:


  • Gsd34me
    started a topic Tips for the wire welder

    Tips for the wire welder

    How often should a guy be going through tips?I am using flux core wire and it seems that i have to replace the tip quite often because the wire will quit feeding do to all the build up of gunk.
Working...
X