Tweet
Picked up one of those CFH flow checkers on eBay to check my welding gas regulators/flow meters. All I can say is wow. My tig flow meter was right on. My Miller supplied mig regulator was off on the low side, I had to turn the reg up to 30cfh to get 20cfh at the gun. And my preset Lincoln reg was set at like 40cfh. This thing will pay for itself in gas savings in no time.
-
MM 211 W/ Spoolgun
Diversion 180
Spectrum 375 X-TREME
Portable Victor O/A
Palmgren Bench Drill Press
14" Evolution Dry Saw
IR 60 Gal. 3 HP Compressor
Speedglas 9100x
My Brain -
I'm glad you posted that. I've had that thing in my shopping cart on eBay for about two years and haven't pulled the trigger. -
I forgot to mention you have to convert L/min to CFHMM 211 W/ Spoolgun
Diversion 180
Spectrum 375 X-TREME
Portable Victor O/A
Palmgren Bench Drill Press
14" Evolution Dry Saw
IR 60 Gal. 3 HP Compressor
Speedglas 9100x
My BrainComment
-
.
*******************************************
The more you know, The better you know, How little you know
“The bitterness of poor quality remains long after the sweetness of low price is forgotten”
Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...
My Blue Stuff:
Dynasty 350DX Tigrunner
Dynasty 200DX
Millermatic 350P w/25ft Alumapro & 30A
Millermatic 200
TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000
Comment
-
You are correct, mine was 3.30$ I'll covert to save $12.00Originally posted by H80N View Post
ive been known to be cheapMM 211 W/ Spoolgun
Diversion 180
Spectrum 375 X-TREME
Portable Victor O/A
Palmgren Bench Drill Press
14" Evolution Dry Saw
IR 60 Gal. 3 HP Compressor
Speedglas 9100x
My BrainComment
-
You could make your own marks on there once you figure out the conversion. Then you don't have to do the conversion anymore.Comment
-
We use one when we have long runs of gas line up to our feeders at elevation and our bottle bank is in the ground.Lincoln Idealarc 250
Miller Bobcat 250
Thermal Arc Hefty 2 feeder
Thermal Dynamics Cutmaster 52
Torchmate CNC tableComment
-
They are a cheap way to verify actual flow at the nozzle.
*******************************************
The more you know, The better you know, How little you know
“The bitterness of poor quality remains long after the sweetness of low price is forgotten”
Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...
My Blue Stuff:
Dynasty 350DX Tigrunner
Dynasty 200DX
Millermatic 350P w/25ft Alumapro & 30A
Millermatic 200
TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000Comment
-
Better than pointing it at your eye that's for sure......if there's a welder, there's a wayComment
-
.
*******************************************
The more you know, The better you know, How little you know
“The bitterness of poor quality remains long after the sweetness of low price is forgotten”
Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...
My Blue Stuff:
Dynasty 350DX Tigrunner
Dynasty 200DX
Millermatic 350P w/25ft Alumapro & 30A
Millermatic 200
TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000Comment
-
-
creeps me out too..............Originally posted by Aeronca41 View Post
.
*******************************************
The more you know, The better you know, How little you know
“The bitterness of poor quality remains long after the sweetness of low price is forgotten”
Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...
My Blue Stuff:
Dynasty 350DX Tigrunner
Dynasty 200DX
Millermatic 350P w/25ft Alumapro & 30A
Millermatic 200
TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000Comment
-
Haha. I just had to bring it up
if there's a welder, there's a wayComment
-
I still put the torch near my cheek to feel if the shielding gas is flowing. But that would be the post flow anyway. Not really interested in tickling my face with the HF.Comment
-
Ive tried that but I can't tell if its gas or the heat radiating off my glowing red cup....
Its a problem. Now I just look for the gold sheen in my weld and if its there, I am happy.if there's a welder, there's a wayComment
Comment