Tweet
Originally posted by H80N
View Post
-
Will give it a try I have blown through barrel and it is free but will take it off and blow it all out. Keeping fingers crossed it works. My students are looking forward to leaning a little aluminum welding this year. Going to put in for a TIG next year as well we will see. Thank for everyone's help. -
PLS keep us posted...................Originally posted by DDenny View Post
.
*******************************************
The more you know, The better you know, How little you know
“The bitterness of poor quality remains long after the sweetness of low price is forgotten”
Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...
My Blue Stuff:
Dynasty 350DX Tigrunner
Dynasty 200DX
Millermatic 350P w/25ft Alumapro & 30A
Millermatic 200
TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000
Comment
-
Well that didn't work!!! On to a new solution. Have a call into Miller warranty to see how they can help.Originally posted by H80N View Post
PLS keep us posted...................Comment
-
Sorry to hear that..... what have we missed...??Originally posted by DDenny View Post.
*******************************************
The more you know, The better you know, How little you know
“The bitterness of poor quality remains long after the sweetness of low price is forgotten”
Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...
My Blue Stuff:
Dynasty 350DX Tigrunner
Dynasty 200DX
Millermatic 350P w/25ft Alumapro & 30A
Millermatic 200
TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000Comment
-
I think it might be the valve within the trigger system. If there is a piece of lent there it might just lodged in there good. I didn't run a lot of pressure through it wasn't sure about the system if I could ruin something. I only oushed about 40 psi backwards through it. I can turn up the compressor valve and run 100psi back through the trigger and see if that does the trick but like I said not sure of the valve setup and if I will ruin something in the triggerOriginally posted by H80N View PostComment
-
At this point I would see what Miller customer service says....
sounds like you have done all the right stuff
maybe they have some ideas or...might need to exchange it for another one,,,,,,,,,Last edited by H80N; 10-04-2016, 11:28 AM..
*******************************************
The more you know, The better you know, How little you know
“The bitterness of poor quality remains long after the sweetness of low price is forgotten”
Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...
My Blue Stuff:
Dynasty 350DX Tigrunner
Dynasty 200DX
Millermatic 350P w/25ft Alumapro & 30A
Millermatic 200
TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000Comment
-
Guessing you pulled the trigger when you shot air thru it?
www.facebook.com/outbackaluminumwelding
Miller Dynasty 700...OH YEA BABY!!
MM 350P...PULSE SPRAYIN' MONSTER
Miller Dynasty 280 with AC independent expansion card
Miller Dynasty 200 DX "Blue Lightning"
Miller Bobcat 225 NT (what I began my present Biz with!)
Miller 30-A Spoolgun
Miller WC-115-A
Miller Spectrum 300
Miller 225 Thunderbolt (my first machine bought new 1980)
Miller Digital Elite Titanium 9400
Comment
-
Update the valve was bad the dealer did an even swap with a new one. Good little spoolgun but the learning curve from steel to aluminum is high. So far this spoolgun works great and is easy to use. Thanks again for every ones suggestions and help I appreciate it.Comment
Comment