spool gun for older machine

[H80N]

Bigal-I have a 4- pin spoolmatic 1 I would be willing to part with. I think it would be a direct connect to your ser. no. machine. I bought it (used) for my old MM200 but never hooked it up, and can do the little AL work I might do with my MM211. PM me and we can talk if you're interested. Hang on to that MM200; my MM200 is probably the best $500 I ever spent-just love that machine.

The Spoolmatic-1 was a high quality...Heavy Duty industrial spoolgun...and having direct connect with the 4pin sure makes hookup easy..

https://www.millerwelds.com/files/ow...O1210J_MIL.pdf

[Aeronca41]

Bigal-I have a 4- pin spoolmatic 1 I would be willing to part with. I think it would be a direct connect to your ser. no. machine. I bought it (used) for my old MM200 but never hooked it up, and can do the little AL work I might do with my MM211. PM me and we can talk if you're interested. Hang on to that MM200; my MM200 is probably the best $500 I ever spent-just love that machine.

[H80N]

ok thank you, I'll look around thanks for your help

you should be able to find a good one in the $500 range....

BTW... the 15A is as good... it's just 15ft long instead of the 30ft of the 30A...

otherwise it is the same gun...

[bigal]

ok thank you, I'll look around thanks for your help

[H80N]

do you know of an economical gun that I can adaptor to this machine with or without and adaptor

I would look for a good used Spoolmatic 30A ...

keep your eyes open on Ebay & CL...... they are bulletproof workhorses and will maintain their resale value if you ever decide to sell

PLUS... they can be made to work... on just about any Miller MIG that you upgrade to in the future

[bigal]

do you know of an economical gun that I can adaptor to this machine with or without and adaptor

[H80N]

thank you

Hope that helps...

Hang on to that MM200... they are a real gem.... it will perform as well as a new MM252.... just not as fancy...

[bigal]

thank you

[H80N]

Hee is a link to the "Spoolgun Hookup Chart"

it will tell you what adaptors/kits are required for which gun...to work on your MM200...

https://www.millerwelds.com/support/...n-hookup-chart

[bigal]

I checked the serial # again it reads JH292654 and its has the black face and in the lower right corner it has a 4-pin connecter that says spoolmatic over and shows a pic. of a spool gun

[H80N]

hello I have an older millermatic 200 ser# JH292654 that purchased new back in that mid 90s it has a 4-pin connector socket for the spool gun , can't find a spoolmatic #1that I was told is a direct connect, looking for a gun that will fit,Just doing light hobby work

Could you pls doublecheck your serial number... I m not finding a manual for that one...

is this a white or black face machine..??

some of the later MM200's had the 14pin connector that allowed direct connect to a spoolguns like the Spoolmatic-3

See Section 4-10 Installation of Optional Spoolgun page 22 (page 28 of the PDF)

https://www.millerwelds.com/files/ow...O1303P_MIL.pdf

[bigal]

hello I have an older millermatic 200 ser# JH292654 that purchased new back in that mid 90s it has a 4-pin connector socket for the spool gun , can't find a spoolmatic #1that I was told is a direct connect, looking for a gun that will fit,Just doing light hobby work