Announcement

Collapse
No announcement yet.

Miller 350 mig voltage question

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • mikesystem
    replied
    I am Hoping that's all
    It is I am wondering if the xr gun is bad

    Leave a comment:


  • H80N
    replied
    Originally posted by mikesystem View Post
    He said it welds steel fine just not so great on aluminum
    would still reset clean and adjust tension...

    Make sure you are Running 100% Argon.. or Ar/He mix for Al....

    instead of the C10 or C25 for steel
    Last edited by H80N; 12-11-2015, 10:54 AM.

    Leave a comment:


  • mikesystem
    replied
    He said it welds steel fine just not so great on aluminum

    Leave a comment:


  • mikesystem
    replied
    It's a xr gun it has got 83 hours on it I bought it I pick it up Monday see if I can get it to work

    Leave a comment:


  • H80N
    replied
    Originally posted by mikesystem View Post
    I know where there is another one I 350p single phase. What the guy says the aluminum welds are getting dirty and is starting to burn tips any idea what would cause the problems
    If it were mine.... FIRST... I would clean or replace gun liner & liner tub on the push-pull gun...

    do full system reset to factory defaults
    (OM-1327 Page 36 5-8. System Reset)

    https://www.millerwelds.com/files/ow...O1327S_MIL.pdf

    set the tension as per manual guidelines... CURL..

    weld parameter for filler and material being welded...

    it's all in the book...

    so many times "operator tweaks" have maladjusted these machines... and starting at a known baseline is a good idea...

    Which push-pull gun..XR??... 30A??

    Last edited by H80N; 12-11-2015, 08:24 AM.

    Leave a comment:


  • mikesystem
    replied
    I know where there is another one I 350p single phase. What the guy says the aluminum welds are getting dirty and is starting to burn tips any idea what would cause the problems

    Leave a comment:


  • H80N
    replied
    Originally posted by mikesystem View Post
    ya thats the down side of it but at least its single phase
    Yup... there is that.....

    Leave a comment:


  • mikesystem
    replied
    ya thats the down side of it but at least its single phase

    Leave a comment:


  • H80N
    replied
    Originally posted by mikesystem View Post
    here what the rear tag says

    serial no LH230001B
    stock no 907167
    volts 460/575
    hertz 60
    phase kw amp
    1 11.4 30/24
    3 6 15/12
    Looks like you can run single or three phase at 460 or 575 vac.... might be able to find a step up transformer to run 230 vac... It may end up being more expensive than it's worth though...

    here is the manual that should match it

    https://www.millerwelds.com/files/ow...O1327S_MIL.pdf

    Last edited by H80N; 12-10-2015, 08:47 PM.

    Leave a comment:


  • mikesystem
    replied
    here what the rear tag says

    serial no LH230001B
    stock no 907167
    volts 460/575
    hertz 60
    phase kw amp
    1 11.4 30/24
    3 6 15/12

    Leave a comment:


  • cruizer
    replied
    Nope, your hooped here, lots of these industrial welders floating around for cheap, cause they are kinda useless after they get auctioned off from their shop

    Leave a comment:


  • mikesystem
    replied
    I will get it tonight and post back give me a few hours thanks for reply

    Leave a comment:


  • H80N
    replied
    Originally posted by mikesystem View Post
    Hi I have been at a old used 350 mig no pulse. The problem is its 460/575-3ph. Can it be rewired to 220 single phase power ? Or do I need rotary converter and transformer thanks
    Serial number pls.....

    there is a 460/575-3ph only version... pics of the Serial# & Stock# label on the back...???

    My own MM350P is the 200/230/460 volt 1 or 3 phase version...
    Last edited by H80N; 12-10-2015, 11:53 AM.

    Leave a comment:


  • mikesystem
    started a topic Miller 350 mig voltage question

    Miller 350 mig voltage question

    Hi I have been at a old used 350 mig no pulse. The problem is its 460/575-3ph. Can it be rewired to 220 single phase power ? Or do I need rotary converter and transformer thanks
Working...
X