Announcement

Collapse
No announcement yet.

180 autoset pipping and splatter

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Cgotto6
    replied
    What voltage do you get on each hot leg?

    Leave a comment:


  • Broccoli1
    replied
    It's possible that low voltage supply can affect the 180 but I would find a solid 230-240v supply somewhere and test it before spending money on a Boost Transformer.

    The liner could have had a burr/dirt in it.

    Drive Roll tension could have been set incorrectly allowing the wire to slip.

    Leave a comment:


  • gulchroad
    replied
    Hi all,
    Changed the liner, tip, nozzle and switched to Lincoln wire from Home depot. (heard from someone on internet it was good) Welder running ok now.
    Anyone out there have a recommendation for the best wire for this welder?

    Using .030 hard wire, gas 25psi.(on regulator dial) with trigger pulled. C25 gas, polarity good.

    Also, had issues year ago with weld quality using auto set. so i started using manual setting, which worked fine. until yesterday. but today all good.

    The voltage at my shop power panel is 209VAC. I'm using 8 gauge wire to connect welder. The welder says 230V on back. not sure if the welder would run with less splatter if i used a boost transformer to bump up voltage to 230V.

    Thanks for your help.

    Leave a comment:


  • nfinch86
    replied
    Correct Polarity ????

    Originally posted by gulchroad View Post
    I have always had splatter with this welder, nozzle clogging up. But recently took my welder to jobsite to weld up steel table. The welds at the jobsite were poor and there was a lot of popping and platter. The welds continued to be popping and poor after I connected it at home. I Recently moved into my new new shop and continue to have poor welds.The power where I live is 220v. Also wondering if there is a different internal connection for this lower voltage? I have work piling up and no useable welder. Wondering if anyone has run into this problem? And found a solution. Thanks in advance for your help
    Are you running hard wire or flux - core ?
    Do you have the machine set correctly ( polarity ) for the wire you're using ?

    Norm

    Leave a comment:


  • Broccoli1
    replied
    Can you give us more details:

    Wire size, CFH gas flow setting

    Does it perform poorly when NOT on Auto Set?

    Leave a comment:


  • Broccoli1
    replied
    Originally posted by Cgotto6 View Post
    This welder only runs on 220v. Don't understand what lower voltage your talking about.
    220v instead of 240v. But that won't make a difference for the OP.

    Leave a comment:


  • gulchroad
    replied
    Originally posted by H80N View Post
    Maybe a bad ground/work connection,,, wire brush the clamp and check all connections...

    may also be a pulled or damaged conductor/conduit in the gun from dragging by the gun...
    I replaced the ground clamp with what i thought was a copper plated one a while back, but looks like a brass one. Ill look into replacing gun cable assembly.
    I also noticed the gun cable gets warm after welding for a while.

    Leave a comment:


  • walker
    replied
    Replace the crappy ground clamp.

    Leave a comment:


  • H80N
    replied
    Originally posted by gulchroad View Post
    I have always had splatter with this welder, nozzle clogging up. But recently took my welder to jobsite to weld up steel table. The welds at the jobsite were poor and there was a lot of popping and platter. The welds continued to be popping and poor after I connected it at home. I Recently moved into my new new shop and continue to have poor welds.The power where I live is 220v. Also wondering if there is a different internal connection for this lower voltage? I have work piling up and no useable welder. Wondering if anyone has run into this problem? And found a solution. Thanks in advance for your help
    Maybe a bad ground/work connection,,, wire brush the clamp and check all connections...

    may also be a pulled or damaged conductor/conduit in the gun from dragging by the gun...

    Leave a comment:


  • Cgotto6
    replied
    This welder only runs on 220v. Don't understand what lower voltage your talking about.

    Leave a comment:


  • gulchroad
    started a topic 180 autoset pipping and splatter

    180 autoset pipping and splatter

    I have always had splatter with this welder, nozzle clogging up. But recently took my welder to jobsite to weld up steel table. The welds at the jobsite were poor and there was a lot of popping and platter. The welds continued to be popping and poor after I connected it at home. I Recently moved into my new new shop and continue to have poor welds.The power where I live is 220v. Also wondering if there is a different internal connection for this lower voltage? I have work piling up and no useable welder. Wondering if anyone has run into this problem? And found a solution. Thanks in advance for your help
    Last edited by gulchroad; 09-28-2014, 09:07 AM.
Working...
X