Announcement

Collapse
No announcement yet.

DYNASTY 700 Arc Starting is a JOKE

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Electric4Life
    started a topic DYNASTY 700 Arc Starting is a JOKE

    DYNASTY 700 Arc Starting is a JOKE

    The hi-frequency starts are non-exsistent. Establishing arc requires either a lot of patients as the arc stumbles continuously, or with a light scratch of the tungsten to the material. I personally own a Maxstar 150 with lift arc and I've been using a similar technique with the Dynasty to get it to start (I'm only comparing arc starting here and I get fed up with $17K+ machine performing the same as a sub $1K unit)

    Miller has replaced the boards in all 5 units once already. The starts were crisp for about a week and slowly trailed off yet again. They were purchased in early 2008. The issue isn't only with AC but DC as well. Maybe I'm missing something here.

    Currently we are welding a ton of Alumium assemblies which require between 320 and 360 Amps. We have a variety of tungsten being used thruought the dapartment, though I choose 1% Zirconiated. Good ground. NEW Speedway 320 torch, almost 20 CFH on the argon, and no contaminated tungsten. Additionally, I wait for the tungsten to properly cool before repositioning after exstinguishing the arc.

    The Dynastys are great machines however this issue is quite time consuming

  • Electric4Life
    replied
    Old Dogs/New Tricks

    2% Ceriated is IN...
    Tried with a conical shape on tip, no bueno. Took Balance out and balled "slightly" allows for a smoother puddle that "wets" in better. A pointed tip distorts the puddle too much. (in my opinion and particular application).
    Arc starts are improving a bit with a "smaller" ball. That 1% Zirconiated IS garbage!! I sure as **** enjoy having ALL the adjustment capabilities that the Dynastys have. Been fussing with them all day


    Old dogs have better tricks and new tricks aren't as hard to learn when you keep an open mind!!

    Leave a comment:


  • 4sfed
    replied
    It's been a while since I changed the coolant. Couldn't hurt to give it a try.

    Leave a comment:


  • ironrail
    replied
    Originally posted by 4sfed View Post
    How does the coolant help? My 300DX has had the same problem from day one.

    Thanks
    Coolant flows through your power cable , over time it can become contaminated and conductive to the high frequency wave.Electricity always finds the easiest path.Too much gas or a surge of gas hurts starting as well.

    Leave a comment:


  • Electric4Life
    replied
    I changed over to Lanthanated yesterday with a 60 degree point with a flat half the diameter of the tungsten.
    What a difference. I decided to go back to Soft/Same and turned the Bal up to 75% from 71% with ACF down to 115from 125. The major concern was how the arc effected the molten pool. Going from a large "ball" to a "point" really shows how the metal is manipulated by the more focused arc, especially before it's up to the proper temperature. It reminded me of welding Al with OA
    I went back in and switched to Advanced/Independent and gave it the EN100 & EP67 with Bal of 75% and ACF 120. I know you fellas suggested 2% Lanthanated but all I had was 1.5% (not the same), so this AM Im prepping out some 2% Ceriated and I'm sure this will be good

    Thank You all

    Leave a comment:


  • mniadna
    replied
    Field Form

    Petesc,
    Where can I find the field form you are referencing?

    Leave a comment:


  • Portable Welder
    replied
    I have approximately a 7 year old dynasty 300DX that does the samething and I use the low conductive coolant from Miller so I dont think coolant is the issue as one person mentioned.
    I use the 2% Lanthanated ( The gold Band ) The type that came with the machine.

    I've kinda gotten use to having to scratch the tungsten on my work piece before hitting the pedal.

    I also agree that its a little time consuming having to do this when trying to get the job done.

    Leave a comment:


  • Helios
    replied
    Originally posted by TJS View Post
    There is even a miller rep. out there on youtube stating to touch the work before striking an arc. I do it as second nature with my 300DX machine.
    I do that also with my Sync250 and it seems to make arc starting more reliable.

    Leave a comment:


  • 4sfed
    replied
    Originally posted by ironrail View Post
    Use 2% lanthanated or ceriated ground to a 30deg. blunted point. Change your coolant,use low conductive coolant ...
    How does the coolant help? My 300DX has had the same problem from day one.

    Thanks

    Leave a comment:


  • petesc
    replied
    Have you talked to anyone from Miller Service to see if there is a HF coupling coil Modifcation you can do like on the Maxstar 200s and Dynasty 200s. Its very simple and it really makes a difference in the starting. Just add one extra wrap on the ferrite core for a total of 4 1/2 turns and regap points to .016 as per Miller field FORM: F217 608E. This for all Maxstar 200s and Dynasty 200s with Serial Numbers Between LC374378 And LJ280221L

    Leave a comment:


  • awill4x4
    replied
    Unfortunately there's nothing that can be done about it.
    When my friend bought his pre "blue lightning" Dynasty 350 we referred to it as the most expensive scratch start Tig money can buy. (we were wrong, obviously the pre blue lightning Dyn 700 was)
    We tried all the internal settings to no avail. Boards were swapped by the Miller techs and we then tried another 2 machines until the local welding dealer finally sourced a Blue Lightning machine and it was ok from then on.
    It was a very frustrating exercise for us particularly since we've been used to excellent start characteristics from some of the European and Japanese inverter Tigs we also use.
    The blue lightning Dyn 350 though is a truly fantastic machine.
    Regards Andrew from Oz.

    Leave a comment:


  • ironrail
    replied
    Use 2% lanthanated or ceriated ground to a 30deg. blunted point. Change your coolant,use low conductive coolant,and I think in the hidden menu you can make an adjustment for tungsten size.

    Leave a comment:


  • FusionKing
    replied
    I have a pre-Blue Lightning 700 as well
    #1 I wouldn't use zirc. on that machine. Use what is recommended. I use lanthanated. I use GOLD but blue should hold up even better. Just what my LWS carries. Ceriated (orange) is also rated well with some people, including Miller.
    If you let the tungsten form a ball it will have the starting issues much more. It should be pointed. Zirconiated is known to form a nice ball for the old transformer machines. I have a pile of it still laying around from back in the day. (2%)
    Get rid of it.....it's junk on that machine. Unless you have it set on sine and all that goes with it like 50% balance and 60 frequency I see no good choosing that

    #2 You can simply touch the cup to the work before you light off and it normally helps a ton

    #3 Why do you need to wait for your tungsten to cool? Sounds like a waste of argon to me

    I also had my boards changed on my machine as well and no problems since. Altho it was an upgrade not a starting issue.
    I hope you get this problem solved quickly....good luck.
    HTH!
    Garry

    Leave a comment:


  • TJS
    replied
    There is even a miller rep. out there on youtube stating to touch the work before striking an arc. I do it as second nature with my 300DX machine.

    Leave a comment:


  • Steve HR Hooligan
    replied
    Wow that sounds bad, could be an opportunity for miller to do some r&d and find out what the problem is and fix the issue, i had the same problem with a lincoln precision tig 375 with welding lost of aluminum castings and the high freq would be be hit and miss

    Leave a comment:

Working...
X