Announcement

Collapse
No announcement yet.

Hey Curizer Quick Question???

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Railmen
    replied
    Awesome that is just what I was looking for.....

    Thx Jeff, you are the man.......

    Railmen

    Leave a comment:


  • cruizer
    replied
    Originally posted by Railmen View Post
    Hey buddy can i hook my 60 series or a 22A feeder to a invertec 350PRO???

    Thx Railmen
    Sure, I do it all the time, generally though I stick a single pole 24 vac relay into the Miller feeder as the lincoln is merely crosses dry contacts "C" & "D", where as the Miller is sending out a 24Vac signal off "B"

    So:

    Miller____ Lincoln

    A _______ N
    B________ goes to one coil side of the 24 Vac relay
    G _______ is twinned with one side going to the other coil side of the relay
    G _______with the other going to "I"

    C&D go to the normally open contacts of the relay

    And yes the 14 pin amphenols are the same, however the Lincoln is "Clocked" to "X", ie, the insert is rotated so that the amphenol plug lines up with the "X" on the insert
    Last edited by cruizer; 06-27-2012, 10:57 AM.

    Leave a comment:


  • H80N
    replied
    Originally posted by Railmen View Post
    I guess the question should be, does the 350Pro have 24VAC to run Miller feeders.....

    Railmen
    The V350 Pro has 5.5 amps 24vac available at the 14pin...... the 22 feeder wants 7 amps and the 60(70) wants 10amps....
    (Note:V350 Pro 24vac circuit fused for 6amps)

    Miller PSA-2 power adaptor has 7-8 amps 24vac output (depending on literature version)

    Miller PSA-115/24 power adaptor has 8 amps 24vac output

    Miller lit says a PSA-2 is ok for an S-74 feeder...

    Leave a comment:


  • Railmen
    replied
    Originally posted by Cornerstone View Post
    Last I heard,he's vacationing.
    Ok sounds good

    Leave a comment:


  • Cornerstone
    replied
    Originally posted by Railmen View Post
    I guess...................
    Last I heard,he's vacationing.

    Leave a comment:


  • H80N
    replied
    Same Connector??

    It DOES look like they both use the same Amphenol connector... if so it will be a matter of matching pinouts.. and outputs

    http://www.heatandweld.com/store/p/4...R-LINCOLN.aspx

    I would be amazed if the pinouts actually matched each other.. although I am encouraged that the lincoln has pins for both 24vac and 115vac.... anybody know for sure

    such a thing would be oh too logical and practical....
    Last edited by H80N; 06-26-2012, 05:42 PM.

    Leave a comment:


  • H80N
    replied
    Adaptor cables....

    Originally posted by Railmen View Post
    Hey buddy can i hook my 60 series or a 22A feeder to a invertec 350PRO???

    Thx Railmen
    Start by checking the available adaptor cables in section F-1 in the manual... against the Feeder's cable pinout.. [Lincoln does have adaptors with 14 pin cable that may work)]

    http://www.lincolnelectric.com/asset...oln3/im679.pdf

    Leave a comment:


  • Railmen
    replied
    Originally posted by diamondback View Post
    Then you can also make the requested connection. It only takes money.
    I guess...................

    Leave a comment:


  • diamondback
    replied
    Originally posted by Railmen View Post
    Sure can, It only takes money....

    Railmen
    Then you can also make the requested connection. It only takes money.

    Leave a comment:


  • Railmen
    replied
    I guess the question should be, does the 350Pro have 24VAC to run Miller feeders.....

    Railmen

    Leave a comment:


  • Railmen
    replied
    Originally posted by diamondback View Post
    Can you swap a duramax for a powerstroke?
    Sure can, It only takes money....

    Railmen

    Leave a comment:


  • walker
    replied
    I don't see why not, I hooked my 50 series to my TB, connect up the 14 pin and go.

    Leave a comment:


  • diamondback
    replied
    Can you swap a duramax for a powerstroke?

    Leave a comment:


  • Railmen
    started a topic Hey Curizer Quick Question???

    Hey Curizer Quick Question???

    Hey buddy can i hook my 60 series or a 22A feeder to a invertec 350PRO???

    Thx Railmen
Working...
X