Announcement

Collapse
No announcement yet.

Service / Technical Manuals?

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Highpwr
    started a topic Service / Technical Manuals?

    Service / Technical Manuals?

    Is there a place where the average Joe can purchase Service / Technical Manuals for Miller welders?

  • Maviday
    replied
    I need the TECH/SERVICE MANUAL for my Millermatic 130XP. In particular I'd love the circuit board diagram.

    Leave a comment:


  • gangakishna
    replied
    miller 150stl

    Originally posted by cruizer View Post
    Which manual were you after?
    i am after miller 150stl service (not user) manual thanking you gangakishna@yahoo.com

    Leave a comment:


  • gangakishna
    replied
    service manual

    Originally posted by cruizer View Post
    Which manual were you after?
    i am seeking service manual for maxstar 150stl serial n0, lj330274j ,new here, hope i am doing the right thing with this reply, thanking you gangakishna@yahoo.com

    Leave a comment:


  • gangakishna
    replied
    service manual

    Originally posted by KClark View Post
    Sorry folks just recieved coorespondance from Miller stating that the Service/Technical Manuals are not available to the average joe from them. They are only available to Distributors and Miller Certified Repair Techs... Bummer!
    it is the average joe that supports their industry

    Leave a comment:


  • gangakishna
    replied
    service manual, not user manual

    Originally posted by cruizer View Post
    There are NO service'/ tech manuals on this site. you can buy them, or if its a under a 5mb file, I can email one to you.
    would appreciate such ,it is miller maxstar 150stl serial n0,lj330274j thanking you gangakishna@yahoo.com or if i can get the detailed electronic circuit diagram,(not electrical diagram) that would be good also bye

    Leave a comment:


  • cruizer
    replied
    Unfortunately, thats likely still under warranty, so no, I'd get into big trouble with the boys at Miller.

    Older non warranty machines sure, but ones still under warranty nope.

    Leave a comment:


  • labmaster02
    replied
    Service / Technical Manuals?

    Cruiser,
    I had talked to you a while back regarding my 211 with the "smooth start" issues while using 230v. I have been looking for the manuals/ schematics. Would have these?
    Thanks.

    Leave a comment:


  • cruizer
    replied
    Which manual were you after?

    Leave a comment:


  • KClark
    replied
    Miller Service Manuals

    Just got an email from Miller. Their Service/Technical Manuals are not available from them to we "Average Joes". Only to their Distributors and Miller Certified Repair Tech and even they have to have certain criteria in order to get them. Bummer

    Leave a comment:


  • KClark
    replied
    Service/Technical Manuals

    Sorry folks just recieved coorespondance from Miller stating that the Service/Technical Manuals are not available to the average joe from them. They are only available to Distributors and Miller Certified Repair Techs... Bummer!

    Leave a comment:


  • 7A749
    replied
    Originally posted by Highpwr View Post
    You got that right 7A749.

    I just like to be as self sufficient as possible that's all. I've got 3 Miller machines in my home shop now, and would just like to have the information available to me to be able to diagnose and repair any simple problems that may come up. It would not be a simple task for me to have to try and get any one of these welders out to a repair shop to get it looked at if I had to.

    I ONLY buy factory repair manuals, whether it be for a vehicle, appliance or whatever. They are the only source of reliable information in my opinion. I don't mind paying for that information - as long as I am allowed access to it.

    If cruizer happens to have that information available that would be awesome. But I have not been able to find anywhere that sells these manuals outright in my on-line searches. So either way I would still be happy just to be ABLE to get the information.

    Thank you for the kind words though.
    Check your PM's

    Leave a comment:


  • 7A749
    replied
    Originally posted by 131RE View Post
    Like Highpwr I have NO qualms about BUYING a manual witness the number of Helms manuals I have and anyone who has purchased them knows a $15 welder manual is low cost! But like him I would love to know where one can both Order one and find a listing of manuals for the various Miller Machines if you are not a registered repair center? Can you order them directly from Miller? Same question re Hobart since they too are part of the same ITW 'family'. Any help-guidance etc in the search for a source for the manuals would be most appreciated.
    Miller will sell you any kind of manual you want, for any machine they have on file.

    They are $15 a piece, last I knew. Just give them a call. They can let you know the skinny on it.

    Leave a comment:


  • 131RE
    replied
    Like Highpwr I have NO qualms about BUYING a manual witness the number of Helms manuals I have and anyone who has purchased them knows a $15 welder manual is low cost! But like him I would love to know where one can both Order one and find a listing of manuals for the various Miller Machines if you are not a registered repair center? Can you order them directly from Miller? Same question re Hobart since they too are part of the same ITW 'family'. Any help-guidance etc in the search for a source for the manuals would be most appreciated.

    Leave a comment:


  • Highpwr
    replied
    Originally posted by 7A749 View Post
    The fact you were up front willing to purchase one says a lot about you. It says you're the kind of guy that knows nothing's free in this world.
    )
    You got that right 7A749.

    I just like to be as self sufficient as possible that's all. I've got 3 Miller machines in my home shop now, and would just like to have the information available to me to be able to diagnose and repair any simple problems that may come up. It would not be a simple task for me to have to try and get any one of these welders out to a repair shop to get it looked at if I had to.

    I ONLY buy factory repair manuals, whether it be for a vehicle, appliance or whatever. They are the only source of reliable information in my opinion. I don't mind paying for that information - as long as I am allowed access to it.

    If cruizer happens to have that information available that would be awesome. But I have not been able to find anywhere that sells these manuals outright in my on-line searches. So either way I would still be happy just to be ABLE to get the information.

    Thank you for the kind words though.

    Leave a comment:

Working...
X