Announcement

Collapse
No announcement yet.

Well, it's not blue...

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Well, it's not blue...



    Newest member of my family.
    Syncrowave 250DX
    Invison 354MP
    XR Control and 30A

    Airco MED20 feeder
    Thermal Dynamics Cutmaster 81
    Smith O/A rig
    And more machinery than you can shake a 7018 rod at

  • #2
    cool, i know a great forum with some of the wisest fellas to help you with hooking it up. lemme know if you want the address

    Comment


    • #3
      Well,Jim.

      A nice machine gray is always welcome in any shop.
      Bob Sigmon
      ___________________
      Dynasty 200DX w/ Coolmate 3
      Miller Passport
      LMSW-52T Spot Welder
      A/O Setup with Meco Midget
      Miller Big Window Elite
      Quincy QT-5HD

      Comment


      • #4
        Nice looking unit. You could always paint it blue. That would look nice next to my milling machine but then there would be no room in my shop for me.
        To all who contribute to this board.
        My sincere thanks , Pete.

        Pureox OA
        Westinghouse 300 amp AC stick
        Miller Syncrowave 250
        Hexacon 250 watt solder iron

        Comment


        • #5
          I'm jelouse.

          Comment


          • #6
            Other than the heavy layer of grunge, she really is a fine machine.

            Single owner, 1974 Voest DA 210 with 16.5" swing and 59" between centers. Induction hardened bedways, D1-6 headstock, and the 7.5hp motor upgrades.

            Of course, that means the 5hp motor I've been sitting on for a phase converter for a couple years is now too small... But Graingers has one on sale for darn near surplus pricing, so I'm picking that up in the morning. Should have her leveled out and running tomorrow.
            Syncrowave 250DX
            Invison 354MP
            XR Control and 30A

            Airco MED20 feeder
            Thermal Dynamics Cutmaster 81
            Smith O/A rig
            And more machinery than you can shake a 7018 rod at

            Comment


            • #7
              I'll give ya $20 for it.

              Comment


              • #8
                lol Yeah, I wish.

                I did get it for significantly less than the 6K they were asking though.
                Syncrowave 250DX
                Invison 354MP
                XR Control and 30A

                Airco MED20 feeder
                Thermal Dynamics Cutmaster 81
                Smith O/A rig
                And more machinery than you can shake a 7018 rod at

                Comment


                • #9
                  Originally posted by Fishy Jim
                  lol Yeah, I wish.

                  I did get it for significantly less than the 6K they were asking though.
                  I'll give you significantly less than what you'r asking for it.

                  Comment


                  • #10
                    And I'll give you significantly less than you'd like to get for what you're offering.

                    Anyway, this one ain't for sale.
                    Syncrowave 250DX
                    Invison 354MP
                    XR Control and 30A

                    Airco MED20 feeder
                    Thermal Dynamics Cutmaster 81
                    Smith O/A rig
                    And more machinery than you can shake a 7018 rod at

                    Comment


                    • #11
                      Well, I tried. Thats definetly a nice lathe.

                      Comment


                      • #12
                        Thanks, I thought so too. lol

                        The paint isn't even too bad once you get the gunk off it.

                        One of the headstock cover screws looked loose and sure enough it was. So I took the cover off figuring the seal was shot - which it was... The gears all look real purdy and nice. There's really no signs of wear on anything inside it.

                        Tomorrow I'll scrape off the crusty old sealant and put a new bead down. Then get the phase converter fired up and make some chips. Now it's time for bed.
                        Syncrowave 250DX
                        Invison 354MP
                        XR Control and 30A

                        Airco MED20 feeder
                        Thermal Dynamics Cutmaster 81
                        Smith O/A rig
                        And more machinery than you can shake a 7018 rod at

                        Comment


                        • #13
                          Sweeeet!!!!!! Your going to love having that.

                          BTW, nice work space too.
                          SolidWorks Premium
                          SolidWorks Simulation Pro
                          MM210 w/3035
                          TA185TSW
                          DG Piranha II
                          Sharpie Deluxe
                          Stars & Stripes BWE
                          Blue Optrel Satellite

                          Comment


                          • #14
                            We've got a lathe that is almost identical to that at school, those are pretty burly machines. All I can say is you are pretty lucky to have something like that all to yourself. (I am very jealous)
                            Owner of Burnt Beard Fabrication & Welding Ltd.

                            BigBlue 500D
                            Dynasty 200DX
                            Millermatic 211
                            4' Box and Pan Break
                            IR compressor

                            Comment


                            • #15
                              Well, the metal shop and all metal classes were closed for lack of funding when I was in HS - so for that, I am jealous of you.
                              Syncrowave 250DX
                              Invison 354MP
                              XR Control and 30A

                              Airco MED20 feeder
                              Thermal Dynamics Cutmaster 81
                              Smith O/A rig
                              And more machinery than you can shake a 7018 rod at

                              Comment

                              Working...
                              X